Power your whole system with the RetroSound® Technophonic amplifier. The Technophonic is a 5-channel amplifier that pushes 65-watts RMS to all four speakers and delivers up to 330-watt RMS to your subwoofer. Switch the Technophonic to 2 or 4 channel modes for radios with only 2 or 4 inputs, and the Technophonic intelligently routes the selected inputs to all five balanced outputs. The Technophonic is 2-ohm or 4-ohm stable and bridgeable, giving you more flexibility to build your system. The low-level RCA inputs allow you to connect the Technophonic effortlessly to your RetroSound radio, or any aftermarket stereo with RCA outputs. Whether you're looking to build a balanced system or going for high power and performance, the Technonphonic amplifier has everything you need.
Crank up the volume without distortion. The Technophonic features low current draw and Class D Digital circuitry, providing exceptional dynamic range and low distortion so you can listen to your favorite songs as loud as you want! High-pass and low-pass filters let you fine-tune your audio for the best listening experience, with remote gain control to adjust bass levels on the fly from the front seat.
- 5-channel amplifier
- Full-range Class D digital circuitry
- 65-watts RMS x 4 channels full-range @ 4 ohms (95-watts RMS x 4 @ 2ohms)
- 225-watts RMS x 1 channel subwoofer @ 4 ohms (330-watts RMS @ 2 ohms)
- Selectable input mode switch for 2, 4, and 5 channel operation
- Bridgeable
- 2-ohm and 4-ohm stable
- Built-in variable low pass and high pass full-range filters
- Bass boost (0-12db) and remote gain control
- Advanced protection circuitry
- Easily connects to your RetroSound radio via RCA inputs
- Works with any aftermarket radio with low-level RCA outputs
- Dimensions: 12.9 in x 5.3 in x 1.87 in (33 cm x 13.4 cm x 4.75 cm)
- Fuse Rating: 60-amp
Optional Wiring Kit
Simplify the installation of your RetroSound® Technophonic amplifier with this convenient wiring kit that includes everything you’ll need to get your 5-channel amplifier installed. The RetroSound 5 Channel Amplifier Wiring Kit comes with: one 60 amp mini-ANL fuse and quality fuse holder, 13 ft (4 m) of 8-gauge red power wire, 5 ft (1.5 m) of 8-gauge black ground wire, 13 ft (4 m) of 18-gauge blue turn-on wire, three sets of RCA cables, two 8-gauge ring terminals, two 18-gauge butt connectors, and a hex key.
Warnings:
California Proposition 65 Warning: WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Note: Please refer to product packaging for the most up to date country of origin.
For more information, see the user's manual, or browse our support page.
Full-Range Power Output @ 4 ohms | 65 watts RMS x 4 channels @ 4 ohms |
Subwoofer Power Output @ 4 ohms | 225 watts RMS x 1 channel @ 4 ohms |
Full-Range Power Output @ 2 ohms | 95 watts RMS x 4 channels @ 2 ohms |
Subwoofer Power Output @ 2 ohms | 330 watts RMS x 1 channel @ 2 ohms |
Full-Range Frequency Response | 24Hz - 65KHz |
Subwoofer Frequency Response | 24Hz - 250Hz |
Total Harmonic Distortion | <0.2% |
Bass Boost | 0-12dB @ 50Hz |
Signal to Noise Ratio (EIA rated) | >95dB |
Input Sensitivity | 200mV - 6.0 volts |
Filter Slope | 24dB |
High Pass Filter (HPF) Frequency Range | 40Hz - 400Hz |
Low Pass Filter (LPF) Frequency Range | 50Hz - 250Hz |
Fuses* (fuse door on bottom of amplifier) | 30 amp ATC Style (x2) |
Dimensions (inches) | 12.9” W x 5.3” D x 1.87” H |
Dimensions (cm) | 33 cm x 13.4 cm x 4.75 cm |
*An additional 60 amp fuse (not included) must be used on the Battery (+) wire at the battery. The fuse must be placed as close as possible to the positive (+) battery terminal (within 6-8 inches away).