An amplifier built for single cab classic trucks and two speaker systems, the Stereophonic 3-Channel amplifier powers your left and right speakers at 65-watts RMS per channel and sends 170-watts RMS to your subwoofer. For radios with only 2 inputs, set the Stereophonics input switch to 2 channel mode and the amplifier intelligently routes the selected inputs to all three balanced outputs. The Stereophonic is 2-ohm and 4-ohm stable and bridgeable, giving you more flexibility to build your system.
The Stereophonic Class D (digital) amplifier allows you to listen to your favorite classic hits at higher volumes with little to no distortion, thanks to its low current draw and exceptional dynamic range. High-pass and low-pass filters let you fine-tune your audio for the best listening experience, with gain and bass boost controls to help dial in the perfect amount of bass.
Features
- 3-channel amplifier
- Full-range Class D digital circuitry
- 65-watts RMS x 2 channels full-range @ 4 ohms
- 170-watts RMS x 1 channel subwoofer @ 4 ohms (229-watts RMS @ 2 ohms)
- Selectable input mode switch for 2 and 3 channel operation
- Bridgeable
- 2-ohm and 4-ohm stable
- Built-in variable low pass and high pass full-range filters
- Bass boost and gain control
- Advanced circuitry and thermal protection
- Easily connects to your RetroSound radio via RCA inputs
- Works with any aftermarket radio with low-level RCA outputs
- Dimensions: 9.4 in x 5.3 in x 1.87 in (24 cm x 13.4 cm x 4.75 cm)
Optional Wiring Kit
Simplify the installation of your RetroSound® Stereophonic amplifier with this convenient wiring kit that includes everything you’ll need to get your 3-channel amplifier installed. The RetroSound 3 Channel Amplifier Wiring Kit comes with: one 30 amp mini-ANL fuse and quality fuse holder, 13 ft (4 m) of 8-gauge red power wire, 5 ft (1.5 m) of 8-gauge black ground wire, 13 ft (4 m) of 18-gauge blue turn-on wire, two sets of RCA cables, two 8-gauge ring terminals, two 18-gauge butt connectors, and a hex key.
Warnings:
California Proposition 65 Warning: WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Note: Please refer to product packaging for the most up to date country of origin.
For more information, see the user's manual, or browse our support page.
| Full-Range Power Output @ 4 ohms | 65 watts RMS x 2 channels @ 4 ohms |
| Subwoofer Power Output @ 4 ohms | 170 watts RMS x 1 channel @ 4 ohms |
| Full-Range Power Output @ 2 ohms | 90 watts RMS x 2 channels @ 2 ohms |
| Subwoofer Power Output @ 2 ohms | 229 watts RMS x 1 channel @ 2 ohms |
| Full-Range Frequency Response | 40Hz - 65KHz |
| Subwoofer Frequency Response | 24Hz - 250Hz |
| Total Harmonic Distortion | <0.2% |
| Signal to Noise Ratio (EIA rated) | >95dB |
| Bass Boost | 0-12dB @ 50Hz |
| Input Sensitivity | 200mV - 6.0 volts |
| Crossover Slope | 24dB |
| High Pass Filter (HPF) Frequency Range | 40Hz - 400Hz |
| Low Pass Filter (LPF) Frequency Range | 50Hz - 250Hz |
| Fuse* (fuse door on bottom of amplifier) | 30 amp ATC Style |
| Dimensions (inches) | 9.4” W x 5.3” D x 1.87” H |
| Dimensions (cm) | 24 cm x 13.4 cm x 4.75 cm |
*An additional 30 amp fuse (not included) must be used on the Battery (+) wire at the battery. The fuse must be placed as close as possible to the positive (+) battery terminal (within 6-8 inches away).
More from collection
